- Mobile NO: +91 98336 40613
- Send Your Mail At: sales@adfastcomponents.com
1.1 This part of EN 10088 specifies the technical delivery conditions for semi-finished products, hot or cold formed bars, rods, wire, sections and bright products of standard grades and special grades of corrosion
resisting stainless steels for general purposes.
1.2 The general technical delivery conditions specified in EN 10021 apply in addition to the specifications of this European Standard, unless otherwise specified in this European Standard.
1.3 This European Standard does not apply to components manufactured by further processing of the product forms listed in 1.1 with quality characteristics altered as a result of such further processing.
| Steel designation | Chemical composition, % by mass | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Steel Name | Steel Number | C max. | Si max. | Mn max | P max. | S | N max | Cr | Mo | Ni | Ti | Others | |
| Standard grades | |||||||||||||
| X2CrNi12 | 1.4003 | 0,030 | 1,00 | 1,50 | 0,040 | ≤ 0,030b | 0,030 | 10,5 to 12,5 | – | 0,30 to 1,00 | – | – | |
| X6Cr13 | 1.4000 | 0,08 | 1,00 | 1,00 | 0,040 | ≤ 0,030b | – | 12,0 to 14,0 | – | – | – | – | |
| X6Cr17 | 1.4016 | 0,08 | 1,00 | 1,00 | 0,040 | ≤ 0,030b | – | 16,0 to 18,0 | – | – | – | – | |
| X6CrMoS17 | 1.4105 | 0,08 | 1,50 | 1,50 | 0,040 | 0,15 to 0,35 | – | 16,0 to 18,0 | 0,20 to 0,60 | – | – | – | |
| X6CrMo17-1 | 1.4113 | 0,08 | 1,00 | 1,00 | 0,040 | ≤ 0,030b | – | 16,0 to 18,0 | 0,90 to 1,40 | – | – | – | |
| Special grades | |||||||||||||
| X2CrTi17 | 1.4520 | 0,025 | 0,50 | 0,50 | 0,040 | ≤ 0,015 | 0,015 | 16,0 to 18,0 | – | – | 0,30 to 0,60 | – | |
| X3CrNb17 | 1.4511 | 0,05 | 1,00 | 1,00 | 0,040 | ≤ 0,030b | – | 16,0 to 18,0 | – | – | – | Nb: 12xC to 1,00 | |
| X2CrMoTiS18-2 | 1.4523 | 0,030 | 1,00 | 0,50 | 0,040 | 0,15 to 0,35 | – | 17,5 to 19,0 | 2,00 to 2,50 | – | 0,30 to 0,80 | (C + N) ≤ 0,040 | |
| X6CrMoNb17-1 | 1.4526 | 0,08 | 1,00 | 1,00 | 0,040 | ≤ 0,015 | 0,040 | 16,0 to 18,0 | 0,80 to 1,40 | – | – | Nb:[7x(C+N)+ 0,10] to 1,00 | |
| X2CrTiNb18 | 1.4509 | 0,030 | 1,00 | 1,00 | 0,040 | ≤ 0,015 | – | 17,5 to 18,5 | – | – | 0,10 to 0,60 | Nb:[(3xC)+0,30] to 1,00 | |
| a Elements not quoted in this table may not be intentionally added to the steel without the agreement of the purchaser except for finishing the cast. All appropriate precautions are to be taken to avoid the addition of such elements from scrap and other materials used in production which would impair mechanical properties and the suitability of the steel. | |||||||||||||
| b Particular ranges of sulphur content may provide improvement of particular properties. For machinability a controlled sulphur content of 0,015 % to 0,030 % is recommended and permitted. For weldability, a controlled sulphur content of 0,008 % to 0,030 % is recommended and permitted. For polishability, a controlled sulphur content of 0,015 % max. is recommended. | |||||||||||||
| Steel designation | Chemical composition, % by mass | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Steel Name | Steel Number | C | Si max. | Mn | P max. | S | Cr | Cu | Mo | Nb | Ni | Others | |
| Standard grades (Martensitic steels)c | |||||||||||||
| X12Cr13 | 1.4006 | 0,08 to 0,15 | 1,00 | ≤ 1,50 | 0,040 | ≤ 0,030b | 11,5 to 13,5 | – | – | – | ≤ 0,75 | – | |
| X12CrS13 | 1.4005 | 0,06 to 0,15 | 1,00 | ≤ 1,50 | 0,040 | 0,15 to 0,35 | 12,0 to 14,0 | – | ≤ 0,60 | – | – | – | |
| X15Cr13 | 1.4024 | 0,12 to 0,17 | 1,00 | ≤ 1,00 | 0,040 | ≤ 0,030b | 12,0 to 14,0 | – | – | – | – | – | |
| X20Cr13 | 1.4021 | 0,16 to 0,25 | 1,00 | ≤ 1,50 | 0,040 | ≤ 0,030b | 12,0 to 14,0 | – | – | – | – | – | |
| X30Cr13 | 1.4028 | 0,26 to 0,35 | 1,00 | ≤ 1,50 | 0,040 | ≤ 0,030b | 12,0 to 14,0 | – | – | – | – | – | |
| X39Cr13 | 1.4031 | 0,36 to 0,42 | 1,00 | ≤ 1,00 | 0,040 | ≤ 0,030b | 12,5 to 14,5 | – | – | – | – | – | |
| X46Cr13 | 1.4034 | 0,43 to 0,50 | 1,00 | ≤ 1,00 | 0,040 | ≤ 0,030b | 12,5 to 14,5 | – | – | – | – | – | |
| X38CrMo14 | 1.4419 | 0,36 to 0,42 | 1,00 | ≤ 1,00 | 0,040 | ≤ 0,015 | 13,0 to 14,5 | – | 0,60 to 1,00 | – | – | – | |
| X50CrMoV15 | 1.4116 | 0,45 to 0,55 | 1,00 | ≤ 1,00 | 0,040 | ≤ 0,030b | 14,0 to 15,0 | – | 0,50 to 0,80 | – | – | V: 0,10 to 0,20 | |
| X55CrMo14 | 1.4110 | 0,48 to 0,60 | 1,00 | ≤ 1,00 | 0,040 | ≤ 0,030b | 13,0 to 15,0 | – | 0,50 to 0,80 | – | – | V: ≤ 0,15 | |
| X14CrMoS17 | 1.4104 | 0,10 to 0,17 | 1,00 | ≤ 1,50 | 0,040 | 0,15 to 0,35 | 15,5 to 17,5 | – | 0,20 to 0,60 | – | – | – | |
| X39CrMo17-1 | 1.4122 | 0,33 to 0,45 | 1,00 | ≤ 1,50 | 0,040 | ≤ 0,030b | 15,5 to 17,5 | – | 0,80 to 1,30 | – | ≤ 1,00 | – | |
| X17CrNi16-2 | 1.4057 | 0,12 to 0,22 | 1,00 | ≤ 1,50 | 0,040 | ≤ 0,030b | 15,0 to 17,0 | – | – | – | 1,50 to 2,50 | – | |
| X3CrNiMo13-4 | 1.4313 | ≤ 0,05 | 0,70 | ≤ 1,50 | 0,040 | ≤ 0,015 | 12,0 to 14,0 | – | 0,30 to 0,70 | – | 3,5 to 4,5 | N: ≥ 0,020 | |
| X4CrNiMo16-5-1 | 1.4418 | ≤ 0,06 | 0,70 | ≤ 1,50 | 0,040 | ≤ 0,030b | 15,0 to 17,0 | – | 0,80 to 1,50 | – | 4,0 to 6,0 | N: ≥ 0,020 | |
| Standard grades (Precipitation hardening steels) | |||||||||||||
| X5CrNiCuNb16-4 | 1.4542 | ≤ 0,07 | 0,70 | ≤ 1,50 | 0,040 | ≤ 0,030b | 15,0 to 17,0 | 3,0 to 5,0 | ≤ 0,60 | 5 x C to 0,45 | 3,0 to 5,0 | – | |
| X7CrNiAI17-7 | 1.4568 | ≤ 0,09 | 0,70 | ≤ 1,00 | 0,040 | ≤ 0,015 | 16,0 to 18,0 | – | – | – | 6,5 to 7,8d | AI: 0,70 to 1,50 | |
| X5CrNiMoCuNb14-5 | 1.4594 | ≤ 0,07 | 0,70 | ≤ 1,00 | 0,040 | ≤ 0,015 | 13,0 to 15,0 | 1,20 to 2,00 | 1,20 to 2,00 | 0,15 to 0,60 | 5,0 to 6,0 | – | |
| Special grades (Martensitic steels)c | |||||||||||||
| X29CrS13 | 1.4029 | 0,25 to 0,32 | 1,00 | ≤ 1,50 | 0,040 | 0,15 to 0,25 | 12,0 to 13,5 | – | ≤ 0,60 | – | – | – | |
| X46CrS13 | 1.4035 | 0,43 to 0,50 | 1,00 | ≤ 2,00 | 0,040 | 0,15 to 0,35 | 12,5 to 14,0 | – | – | – | – | – | |
| X70CrMo15 | 1.4109 | 0,60 to 0,75 | 0,70 | ≤ 1,00 | 0,040 | ≤ 0,030b | 14,0 to 16,0 | – | 0,40 to 0,80 | – | – | – | |
| X40CrMoVN16-2 | 1.4123 | 0,35 to 0,50 | 1,00 | ≤ 1,00 | 0,040 | ≤ 0,015 | 14,0 to 16,0 | – | 1,00 to 2,50 | – | ≤ 0,50 | V: ≤ 1,50 N: 0,10 to 0,30 | |
| X105CrMo17 | 1.4125 | 0,95 to 1,20 | 1,00 | ≤ 1,00 | 0,040 | ≤ 0,030b | 16,0 to 18,0 | – | 0,40 to 0,80 | – | – | – | |
| X90CrMoV18 | 1.4112 | 0,85 to 0,95 | 1,00 | ≤ 1,00 | 0,040 | ≤ 0,030b | 17,0 to 19,0 | – | 0,90 to 1,30 | – | – | V: 0,07 to 0,12 | |
| X2CrNiMoV13-5-2 | 1.4415 | ≤ 0,030 | 0,50 | ≤ 0,50 | 0,040 | ≤ 0,015 | 11,5 to 13,5 | – | 1,50 to 2,50 | – | 4,5 to 6,5 | Ti: ≤ 0,010 V: 0,10 to 0,50 | |
| Special grades (Precipitation hardening steels) | |||||||||||||
| X1CrNiMoAlTi12-9-2 | 1.4530 | ≤ 0,015 | 0,10 | ≤ 0,10 | 0,010 | ≤ 0,005 | 11,5 to 12,5 | – | 1,85 to 2,15 | – | 8,5 to 9,5 | Al: 0,60 to 0,80 Ti: 0,28 to 0,37 N: ≤ 0,010 | |
| X1CrNiMoAlTi12-10-2 | 1.4596 | ≤ 0,015 | 0,10 | ≤ 0,10 | 0,010 | ≤ 0,005 | 11,5 to 12,5 | – | 1,85 to 2,15 | – | 9,2 to 10,2 | Al: 0,80 to 1,10 Ti: 0,28 to 0,40 N: ≤ 0,020 | |
| X5NiCrTiMoVB25-15-2 | 1.4606 | ≤ 0,08 | 1,00 | 1,00 to 2,00 | 0,025 | ≤ 0,015 | 13,0 to 16,0 | – | 1,00 to 1,50 | – | 24,0 to 27,0 | B: 0,0010 to 0,010 Al: ≤ 0,35 Ti: 1,90 to 2,30 V: 0,10 to 0,50 | |
| a Elements not quoted in this table shall not be intentionally added to the steel without the agreement of the purchaser except for finishing the cast. All precautions are to be taken to avoid the addition of such elements from scrap and other materials used in production which would impair mechanical properties and the suitability of the steel. | |||||||||||||
| b Particular ranges of sulphur content may provide improvement of particular properties. For machinability a controlled sulphur content of 0,015 % to 0,030 % is recommended and permitted. For weldability, a controlled sulphur content of 0,008 % to 0,030 % is recommended and permitted. For polishability, a controlled sulphur content of 0,015 % max. is recommended. | |||||||||||||
| c Tighter carbon ranges may be agreed at the time of enquiry and order. | |||||||||||||
| d For better cold deformability, the upper limit may be increased to 8,3 %. | |||||||||||||
| Steel designation | Chemical composition, % by mass | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Steel Name | Steel Number | C | Si | Mn | P max. | S | N | Cr | Cu | Mo | Nb | Ni | Others |
| Standard grades | |||||||||||||
| X10CrNi18-8 | 1.4310 | 0,05 to 0,15 | ≤ 2,00 | ≤ 2,00 | 0,045 | ≤ 0,015 | ≤ 0,11 | 16,0 to 19,0 | – | ≤ 0,80 | – | 6,0 to 9,5 | – |
| X2CrNi18-9 | 1.4307 | ≤ 0,030 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,030b | ≤ 0,11 | 17,5 to 19,5 | – | – | – | 8,0 to 10,5 | – |
| X2CrNi19-11 | 1.4306 | ≤ 0,030 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,030b | ≤ 0,11 | 18,0 to 20,0 | – | – | – | 10,0 to 12,0c | – |
| X2CrNiN18-10 | 1.4311 | ≤ 0,030 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,030b | 0,12 to 0,22 | 17,5 to 19,5 | – | – | – | 8,5 to 11,5 | – |
| X5CrNi18-10 | 1.4301 | ≤ 0,07 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,030b | ≤ 0,11 | 17,5 to 19,5 | – | – | – | 8,0 to 10,5 | – |
| X8CrNiS18-9 | 1.4305 | ≤ 0,10 | ≤ 1,00 | ≤ 2,00 | 0,045 | 0,15 to 0,35 | ≤ 0,11 | 17,0 to 19,0 | ≤ 1,00 | – | – | 8,0 to 10,0 | – |
| X6CrNiTi18-10 | 1.4541 | ≤ 0,08 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,030b | – | 17,0 to 19,0 | – | – | – | 9,0 to 12,0c | Ti: 5 x C to 0,70 |
| X4CrNi18-12 | 1.4303 | ≤ 0,06 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,030b | ≤ 0,11 | 17,0 to 19,0 | – | – | – | 11,0 to 13,0 | – |
| X2CrNiMo17-12-2 | 1.4404 | ≤ 0,030 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,030b | ≤ 0,11 | 16,5 to 18,5 | – | 2,00 to 2,50 | – | 10,0 to 13,0c | – |
| X2CrNiMoN17-11-2 | 1.4406 | ≤ 0,030 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,030b | 0,12 to 0,22 | 16,5 to 18,5 | – | 2,00 to 2,50 | – | 10,0 to 12,5c | – |
| X5CrNiMo17-12-2 | 1.4401 | ≤ 0,07 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,030b | ≤ 0,11 | 16,5 to 18,5 | – | 2,00 to 2,50 | – | 10,0 to 13,0 | – |
| X6CrNiMoTi17-12-2 | 1.4571 | ≤ 0,08 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,030b | – | 16,5 to 18,5 | – | 2,00 to 2,50 | – | 10,5 to 13,5c | Ti: 5 x C to 0,70 |
| X2CrNiMo17-12-3 | 1.4432 | ≤ 0,030 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,030b | ≤ 0,11 | 16,5 to 18,5 | – | 2,50 to 3,00 | – | 10,5 to 13,0 | – |
| X2CrNiMoN17-13-3 | 1.4429 | ≤ 0,030 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,015 | 0,12 to 0,22 | 16,5 to 18,5 | – | 2,50 to 3,00 | – | 11,0 to 14,0c | – |
| X3CrNiMo17-13-3 | 1.4436 | ≤ 0,05 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,030b | ≤ 0,11 | 16,5 to 18,5 | – | 2,50 to 3,00 | – | 10,5 to 13,0c | – |
| X2CrNiMo18-14-3 | 1.4435 | ≤ 0,030 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,030b | ≤ 0,11 | 17,0 to 19,0 | – | 2,50 to 3,00 | – | 12,5 to 15,0 | – |
| X2CrNiMoN17-13-5 | 1.4439 | ≤ 0,030 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,015 | 0,12 to 0,22 | 16,5 to 18,5 | – | 4,0 to 5,0 | – | 12,5 to 14,5 | – |
| X6CrNiCuS18-9-2 | 1.4570 | ≤ 0,08 | ≤ 1,00 | ≤ 2,00 | 0,045 | 0,15 to 0,35 | ≤ 0,11 | 17,0 to 19,0 | 1,40 to 1,80 | ≤ 0,60 | – | 8,0 to 10,0 | – |
| X3CrNiCu18-9-4 | 1.4567 | ≤ 0,04 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,030b | ≤ 0,11 | 17,0 to 19,0 | 3,0 to 4,0 | – | – | 8,5 to 10,5 | – |
| X1NiCrMoCu25-20-5 | 1.4539 | ≤ 0,020 | ≤ 0,70 | ≤ 2,00 | 0,030 | ≤ 0,010 | ≤ 0,15 | 19,0 to 21,0 | 1,20 to 2,00 | 4,0 to 5,0 | – | 24,0 to 26,0 | – |
| Special grades | |||||||||||||
| X5CrNi17-7 | 1.4319 | ≤ 0,07 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,030 | ≤ 0,11 | 16,0 to 18,0 | – | – | – | 6,0 to 8,0 | – |
| X9CrNi18-9 | 1.4325 | 0,03 to 0,15 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,030 | – | 17,0 to 19,0 | – | – | – | 8,0 to 10,0 | – |
| X5CrNiN19-9 | 1.4315 | ≤ 0,06 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,015 | 0,12 to 0,22 | 18,0 to 20,0 | – | – | – | 8,0 to 11,0 | – |
| X6CrNiNb18-10 | 1.4550 | ≤ 0,08 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,015 | – | 17,0 to 19,0 | – | – | 10 x C to 1,00 | 9,0 to 12,0c | – |
| X1CrNiMoN25-22-2 | 1.4466 | ≤ 0,020 | ≤ 0,70 | ≤ 2,00 | 0,025 | ≤ 0,010 | 0,10 to 0,16 | 24,0 to 26,0 | – | 2,00 to 2,50 | – | 21,0 to 23,0 | – |
| X6CrNiMoNb17-12-2 | 1.4580 | ≤ 0,08 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,015 | – | 16,5 to 18,5 | – | 2,00 to 2,50 | 10 x C to 1,00 | 10,5 to 13,5 | – |
| X6CrNiMoNb17-12-2 | 1.4580 | ≤ 0,08 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,015 | – | 16,5 to 18,5 | – | 2,00 to 2,50 | 10 x C to 1,00 | 10,5 to 13,5 | – |
| X2CrNiMo18-15-4 | 1.4438 | ≤ 0,030 | ≤ 1,00 | ≤ 2,00 | 0,045 | ≤ 0,030b | ≤ 0,11 | 17,5 to 19,5 | – | 3,0 to 4,0 | – | 13,0 to 16,0c | – |
| X1CrNiMoCuN24-22-8* | 1.4652* | ≤ 0,020 | ≤ 0,50 | 2,00 to 4,0 | 0,030 | ≤ 0,005 | 0,45 to 0,55 | 23,0 to 25,0 | 0,30 to 0,60 | 7,0 to 8,0 | – | 21,0 to 23,0 | – |
| X1CrNiSi18-15-4 | 1.4361 | ≤ 0,015 | 3,7 to 4,5 | ≤ 2,00 | 0,025 | ≤ 0,010 | ≤ 0,11 | 16,5 to 18,5 | – | ≤ 0,20 | – | 14,0 to 16,0 | – |
| X11CrNiMnN19-8-6 | 1.4369 | 0,07 to 0,15 | 0,50 to 1,00 | 5,0 to 7,5 | 0,030 | ≤ 0,015 | 0,20 to 0,30 | 17,5 to 19,5 | – | – | – | 6,5 to 8,5 | – |
| X12CrMnNiN17-7-5 | 1.4372 | ≤ 0,15 | ≤ 1,00 | 5,5 to 7,5 | 0,045 | ≤ 0,015 | 0,05 to 0,25 | 16,0 to 18,0 | – | – | – | 3,5 to 5,5 | – |
| X8CrMnNiN18-9-5 | 1.4374 | 0,05 to 0,10 | 0,30 to 0,60 | 9,0 to 10,0 | 0,035 | ≤ 0,030 | 0,25 to 0,32 | 17,5 to 18,5 | ≤ 0,40 | ≤ 0,50 | – | 5,0 to 6,0 | – |
| X8CrMnCuNB17-8-3 | 1.4597 | ≤ 0,10 | ≤ 2,00 | 6,5 to 8,5 | 0,040 | ≤ 0,030 | 0,15 to 0,30 | 16,0 to 18,0 | 2,00 to 3,5 | ≤ 1,00 | – | ≤ 2,00 | B: 0,0005 to 0,0050 |
| X3CrNiCu19-9-2 | 1.4560 | ≤ 0,035 | ≤ 1,00 | 1,50 to 2,00 | 0,045 | ≤ 0,015 | ≤ 0,11 | 18,0 to 19,0 | 1,50 to 2,00 | – | – | 8,0 to 9,0 | – |
| X3CrNiCuMo17-11-3-2 | 1.4578 | ≤ 0,04 | ≤ 1,00 | ≤ 1,00 | 0,045 | ≤ 0,015 | ≤ 0,11 | 16,5 to 17,5 | 3,0 to 3,5 | 2,00 to 2,50 | – | 10,0 to 11,0 | – |
| X1NiCrMoCu31-27-4 | 1.4563 | ≤ 0,020 | ≤ 0,70 | ≤ 2,00 | 0,030 | ≤ 0,010 | ≤ 0,11 | 26,0 to 28,0 | 0,70 to 1,50 | 3,0 to 4,0 | – | 30,0 to 32,0 | – |
| X1CrNiMoCuN25-25-5 | 1.4537 | ≤ 0,020 | ≤ 0,70 | ≤ 2,00 | 0,030 | ≤ 0,010 | 0,17 to 0,25 | 24,0 to 26,0 | 1,00 to 2,00 | 4,7 to 5,7 | – | 24,0 to 27,0 | – |
| X1CrNiMoCuN20-18-7 | 1.4547 | ≤ 0,020 | ≤ 0,70 | ≤ 1,00 | 0,030 | ≤ 0,010 | 0,18 to 0,25 | 19,5 to 20,5 | 0,50 to 1,00 | 6,0 to 7,0 | – | 17,5 to 18,5 | – |
| X2CrNiMoCuS17-10-2 | 1.4598 | ≤ 0,030 | ≤ 1,00 | ≤ 2,00 | 0,045 | 0,10 to 0,20 | ≤ 0,11 | 16,5 to 18,5 | 1,30 to 1,80 | 2,00 to 2,50 | – | 10,0 to 13,0 | – |
| X1CrNiMoCuNW24-22-6 | 1.4659 | ≤ 0,020 | ≤ 0,70 | 2,00 to 4,0 | 0,030 | ≤ 0,010 | 0,35 to 0,50 | 23,0 to 25,0 | 1,00 to 2,00 | 5,5 to 6,5 | – | 21,0 to 23,0 | W: 1,50 to 2,50 |
| X1NiCrMoCuN25-20-7 | 1.4529 | ≤ 0,020 | ≤ 0,50 | ≤ 1,00 | 0,030 | ≤ 0,010 | 0,15 to 0,25 | 19,0 to 21,0 | 0,50 to 1,50 | 6,0 to 7,0 | – | 24,0 to 26,0 | – |
| X2CrNiMnMoN25-18-6-5 | 1.4565 | ≤ 0,030 | ≤ 1,00 | 5,0 to 7,0 | 0,030 | ≤ 0,015 | 0,30 to 0,60 | 24,0 to 26,0 | – | 4,0 to 5,0 | ≤ 0,15 | 16,0 to 19,0 | – |
| a Elements not listed in this table shall not be intentionally added to the steel without the agreement of the purchaser except for finishing the cast. All appropriate precautions are to be taken to avoid the addition of such elements from scrap and other materials used in production which would impair mechanical properties and the suitability of the steel. | |||||||||||||
| b Particular ranges of sulphur content may provide improvement of particular properties. For machinability a controlled sulphur content of 0,015 % to 0,030 % is recommended and permitted. For weldability, a controlled sulphur content of 0,008 % to 0,030 % is recommended and permitted. For polishability, a controlled sulphur content of 0,015 % max. is recommended. | |||||||||||||
| c Where for special reasons, e.g. hot workability for the fabrication of seamless tubes where it is necessary to minimize the delta ferrite content, or with the aim of low magnetic permeability, the maximum Ni content may be increased by the following amounts: 0,50 % (by mass): 1.4571 1,00 % (by mass): 1.4306, 1.4406, 1.4429, 1.4436, 1.4438, 1.4541, 1.4550 1,50 % (by mass): 1.4404. | |||||||||||||
| * ) Patented steel grade. | |||||||||||||
| Steel designation | Chemical composition, % by mass | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Steel Name | Steel Number | C max. | Si | Mn | P max. | S max. | N | Cr | Cu | Mo | Ni | Others | |
| Standard grades | |||||||||||||
| X3CrNiMoN27-5-2 | 1.4460 | 0,05 | ≤ 1,00 | ≤ 2,00 | 0,035 | 0,030b | 0,05 to 0,20 | 25,0 to 28,0 | – | 1,30 to 2,00 | 4,5 to 6,5 | – | |
| X2CrNiMoN22-5-3c | 1.4462c | 0,030 | ≤ 1,00 | ≤ 2,00 | 0,035 | 0,015 | 0,10 to 0,22 | 21,0 to 23,0 | – | 2,50 to 3,5 | 4,5 to 6,5 | – | |
| Special grades | |||||||||||||
| X2CrNiN23-4*) | 1.4362*) | 0,030 | ≤ 1,00 | ≤ 2,00 | 0,035 | 0,015 | 0,05 to 0,20 | 22,0 to 24,0 | 0,10 to 0,60 | 0,10 to 0,60 | 3,5 to 5,5 | – | |
| X2CrNiMoN29-7-2*) | 1.4477*) | 0,030 | ≤ 0,50 | 0,80 to 1,50 | 0,030 | 0,015 | 0,30 to 0,40 | 28,0 to 30,0 | ≤ 0,80 | 1,50 to 2,60 | 5,8 to 7,5 | – | |
| X2CrNiMoCuN25-6-3 | 1.4507 | 0,030 | ≤ 0,70 | ≤ 2,00 | 0,035 | 0,015 | 0,20 to 0,30 | 24,0 to 26,0 | 1,00 to 2,50 | 3,0 to 4,0 | 6,0 to 8,0 | – | |
| X2CrNiMoN25-7-4*) | 1.4410*) | 0,030 | ≤ 1,00 | ≤ 2,00 | 0,035 | 0,015 | 0,24 to 0,35 | 24,0 to 26,0 | – | 3,0 to 4,5 | 6,0 to 8,0 | – | |
| X2CrNiMoCuWN25-7-4 | 1.4501 | 0,030 | ≤ 1,00 | ≤ 1,00 | 0,035 | 0,015 | 0,20 to 0,30 | 24,0 to 26,0 | 0,50 to 1,00 | 3,0 to 4,0 | 6,0 to 8,0 | W: 0,50 to 1,00 | |
| X2CrNiMoSi18-5-3 | 1.4424 | 0,030 | 1,40 to 2,00 | 1,20 to 2,00 | 0,035 | 0,015 | 0,05 to 0,10 | 18,0 to 19,0 | – | 2,50 to 3,0 | 4,5 to 5,2 | – | |
| a Elements not listed in this table shall not be intentionally added to the steel without the agreement of the purchaser except for finishing the cast. All appropriate precautions are to be taken to avoid the addition of such elements from scrap and other materials used in production which would impair mechanical properties and the suitability of the steel. | |||||||||||||
| b Particular ranges of sulphur content may provide improvement of particular properties. For machinability a controlled sulphur content of 0,015 % to 0,030 % is recommended and permitted. For weldability, a controlled sulphur content of 0,008 % to 0,030 % is recommended and permitted. For polishability, a controlled sulphur content of 0,015 % max. is recommended. | |||||||||||||
| c By agreement, this grade can be delivered with a Pitting Resistance Equivalent Number (PRE = Cr +3,3Mo + 16N, compare Table C.1 of EN 10088-1) greater than 34. | |||||||||||||
| * ) Patented steel grade. | |||||||||||||
| Steel designation | Thickness t or diameterb d | Hardness | 0,2 %-proof strength | Tensile Strength | Elongation after fractured | Resistance to intergranular corrosione | |||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Steel Name | Steel Number | mm max. | HBc max. | Rp0,2d MPa*) min. | R m d MPa*) | A % min. (long.) | In the delivery condition | In the welded condition | |||||
| Standard grades | |||||||||||||
| X2CrNi12 | 1.4003 | 100 | 200 | 260 | 450 to 600 | 20 | no | no | |||||
| X6Cr13 | 1.4000 | 25 | 200 | 230 | 400 to 630 | 20 | no | no | |||||
| X6Cr17 | 1.4016 | 100 | 200 | 240 | 400 to 630 | 20 | yes | no | |||||
| X6CrMoS17 | 1.4105 | 100 | 200 | 250 | 430 to 630 | 20 | no | no | |||||
| X6CrMo17-1 | 1.4113 | 100 | 200 | 280 | 440 to 660 | 18 | yes | no | |||||
| Special grades | |||||||||||||
| X2CrTi17 | 1.4520 | 50 | 200 | 200 | 420 to 620 | 20 | yes | yes | |||||
| X3CrNb17 | 1.4511 | 50 | 200 | 200 | 420 to 620 | 20 | yes | yes | |||||
| X2CrMoTiS18-2 | 1.4523 | 100 | 200 | 280 | 430 to 600 | 15 | yes | no | |||||
| X6CrMoNb17-1 | 1.4526 | 50 | 200 | 300 | 480 to 680 | 15 | yes | yes | |||||
| X2CrTiNb18 | 1.4509 | 50 | 200 | 200 | 420 to 620 | 18 | yes | yes | |||||
| a Annealing treatment may be omitted, if the conditions for hot working and subsequent cooling are such that the requirements for the mechanical properties of the product and the resistance to intergranular corrosion as defined in EN ISO 3651-2 are obtained. | |||||||||||||
| b Width across flats for hexagons. | |||||||||||||
| c Only for guidance. | |||||||||||||
| d For rods, only the tensile strength values apply. | |||||||||||||
| e When tested according to EN ISO 3651-2. | |||||||||||||
| *) 1MPa = 1 N/mm². | |||||||||||||
| Steel designation | Thickness t or diameter a d | Heat treatment conditionb | Hardness | 0,2 %-proof strength | Tensile Strength | Elongation after fracture | Impact energy (ISO-V) | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Steel Name | Steel Number | mm | HBc max. | Rp0,2d MPa*) min. | R m d MPa*) | Ad % min. | KV J min | ||||||||
| (long.) | (tr.) | (long.) | (tr.) | ||||||||||||
| Standard grades | |||||||||||||||
| X12Cr13 | 1.4006 | – | +A | 220 | – | max. 730 | – | – | – | – | |||||
| ≤ 160 | +QT650 | – | 450 | 650 to 850 | 15 | – | 25 | – | |||||||
| X12CrS13 | 1.4005 | – | +A | 220 | – | max. 730 | – | – | – | – | |||||
| ≤ 160 | +QT650 | – | 450 | 650 to 850 | 12 | – | – | – | |||||||
| X15Cr13 | 1.4024 | – | +A | 220 | – | max. 730 | – | – | – | – | |||||
| ≤ 160 | +QT650 | – | 450 | 650 to 850 | 15 | – | – | – | |||||||
| X20Cr13 | 1.4021 | – | +A | 230 | – | max. 760 | – | – | – | – | |||||
| ≤ 160 | +QT700 | – | 500 | 700 to 850 | 13 | – | 25 | – | |||||||
| +QT800 | – | 600 | 800 to 950 | 12 | – | 20 | – | ||||||||
| X30Cr13 | 1.4028 | – | +A | 245 | – | max. 800 | – | – | – | – | |||||
| ≤ 160 | +QT850 | – | 650 | 850 to 1000 | 10 | – | 15 | – | |||||||
| X39Cr13 | 1.4031 | – | +A | 245 | – | max. 800 | – | – | – | – | |||||
| ≤ 160 | +QT800 | – | 650 | 800 to 1000 | 10 | – | 12 | – | |||||||
| X46Cr13 | 1.4034 | – | +A | 245 | – | max. 800 | – | – | – | – | |||||
| ≤ 160 | +QT800 | – | 650 | 850 to 1000 | 10 | – | 12 | – | |||||||
| X38CrMo14 | 1.4419 | – | +A | 235 | – | max. 760 | – | – | – | – | |||||
| X50CrMoV15 | 1.4116 | – | +A | 280 | – | max. 900 | – | – | – | – | |||||
| X55CrMo14 | 1.4110 | ≤ 100 | +A | 280 | – | max. 950 | – | – | – | – | |||||
| X14CrMoS17 | 1.4104 | – | +A | 220 | – | max 730 | – | – | – | – | |||||
| ≤ 60 | +QT650 | – | 500 | 650 to 850 | 12 | – | – | – | |||||||
| 60 < t ≤ 160 | 10 | – | – | – | |||||||||||
| X39CrMo17-1 | 1.4122 | – | +A | 280 | – | max. 900 | – | – | – | – | |||||
| ≤ 60 | +QT750 | – | 550 | 750 to 950 | 12 | – | 20 | – | |||||||
| 60 < t ≤ 160 | 14 | – | |||||||||||||
| X17CrNi16-2 | 1.4057 | – | +A | 295 | – | max. 950 | – | – | – | – | |||||
| ≤ 60 | +QT800 | – | 600 | 800 to 950 | 14 | – | 25 | – | |||||||
| 60 < t ≤ 160 | 12 | 20 | |||||||||||||
| ≤ 60 | +QT900 | – | 700 | 900 to 1050 | 12 | – | 20 | – | |||||||
| 60 < t ≤ 160 | 10 | 15 | |||||||||||||
| X3CrNiMo13-4 | 1.4313 | – | +A | 320 | – | max. 1100 | – | – | – | – | |||||
| ≤ 160 | +QT700 | – | 520 | 700 to 800 | 15 | – | 70 | – | |||||||
| 160 < t ≤ 250 | – | 12 | – | 50 | |||||||||||
| ≤ 160 | +QT780 | – | 620 | 80 to 980 | 15 | – | 70 | – | |||||||
| 160 < t ≤ 250 | – | 12 | – | 50 | |||||||||||
| ≤ 160 | +QT900 | – | 800 | 900 to 1100 | 12 | – | 50 | – | |||||||
| 160 < t ≤ 250 | – | 10 | – | 40 | |||||||||||
| X4CrNiMo16-5-1 | 1.4418 | – | +A | 320 | – | max. 1100 | – | – | – | – | |||||
| ≤ 160 | +QT760 | – | 550 | 760 to 960 | 16 | – | 90 | – | |||||||
| 160 < t ≤ 250 | 14 | 70 | |||||||||||||
| ≤ 160 | +QT900 | – | 700 | 900 to 1100 | 16 | – | 80 | – | |||||||
| 160 < t ≤ 250 | – | 14 | – | 60 | |||||||||||
| Special grades | |||||||||||||||
| X29CrS13 | 1.4029 | ≤ 160 | +A | 245 | – | max. 800 | – | – | – | – | |||||
| +QT850 | – | 650 | 850 to 1000 | 9 | – | – | – | ||||||||
| X46CrS13 | 1.4035 | ≤ 63 | +A | 245 | – | max. 800 | – | – | – | – | |||||
| X70CrMo15 | 1.4109 | ≤ 100 | +A | 280 | – | max. 900 | – | – | – | – | |||||
| X40CrMoVN16-2 | 1.4123 | ≤ 100 | +A | 280 | – | – | – | – | – | – | |||||
| X105CrMo17 | 1.4125 | ≤ 100 | +A | 285 | – | – | – | – | – | – | |||||
| X90CrMoV18 | 1.4112 | ≤ 100 | +A | 265 | – | – | – | – | – | – | |||||
| X2CrNiMoV13-5-2 | 1.4415 | ≤ 160 | +QT750 | – | 650 | 750 to 900 | 18 | – | 100 | – | |||||
| +QT850 | – | 750 | 850 to 1000 | 15 | – | 80 | – | ||||||||
| a Width across flats for hexagons. | |||||||||||||||
| b +A = annealed, +QT = quenched and tempered. | |||||||||||||||
| c Only for guidance. | |||||||||||||||
| d For rods, only the tensile strength values apply. | |||||||||||||||
| *) 1MPa = 1 N/mm². | |||||||||||||||
| Steel designation | Thickness t or diameter b d | Hardness c,d | 0,2 %-proof strength | 1 %-proof strength | Tensile strengthd,e | Elongation after fractured,e | Impact energy (ISO-V) b | Resistance to intergranular corrosionf | |||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Steel Name | Steel Number | mm | HB max. | Rp0,2e MPa*) min. | R p1,0c,e MPa*) min. | R m MPa*) | A % min | KV J min | in the delivery condition | In the sensitized conditiong | |||
| (long.) | (tr.) | (long.) | (tr.) | ||||||||||
| Standard grades | |||||||||||||
| X10CrNi18-8 | 1.4310 | ≤ 40 | 230 | 195 | 230 | 500 to 750 | 40 | – | – | – | no | no | |
| X2CrNi18-9 | 1.4307 | ≤ 160 | 215 | 175 | 210 | 500 to 700 | 45 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 35 | – | 60 | |||||||||
| X2CrNi19-11 | 1.4306 | ≤ 160 | 215 | 180 | 215 | 460 to 680 | 45 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 35 | – | 60 | |||||||||
| X2CrNiN18-10 | 1.4311 | ≤ 160 | 230 | 270 | 305 | 550 to 760 | 40 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| X5CrNi18-10 | 1.4301 | ≤ 160 | 215 | 190 | 225 | 500 to 700 | 45 | – | 100 | – | yes | no h | |
| 160 < t ≤ 250 | – | 35 | – | 60 | |||||||||
| X8CrNiS18-9 | 1.4305 | ≤ 160 | 230 | 190 | 225 | 500 to 750 | 35 | – | – | – | no | no | |
| X6CrNiTi18-10 | 1.4541 | ≤ 160 | 215 | 190 | 225 | 500 to 700 | 40 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| X4CrNi18-12 | 1.4303 | ≤ 160 | 215 | 190 | 225 | 500 to 700 | 45 | – | 100 | – | yes | no h | |
| 160 < t ≤ 250 | – | 35 | – | 60 | |||||||||
| X2CrNiMo17-12-2 | 1.4404 | ≤ 160 | 215 | 200 | 235 | 500 to 700 | 40 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| X2CrNiMoN17-11-2 | 1.4406 | ≤ 160 | 250 | 280 | 315 | 580 to 800 | 40 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| X5CrNiMo17-12-2 | 1.4401 | ≤ 160 | 215 | 200 | 235 | 500 to 700 | 40 | – | 100 | – | yes | noh | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| X6CrNiMoTi17-12-2 | 1.4571 | ≤ 160 | 215 | 200 | 235 | 500 to 700 | 40 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| X2CrNiMo17-12-3 | 1.4432 | ≤ 160 | 215 | 200 | 235 | 500 to 700 | 40 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| X2CrNiMoN17-13-3 | 1.4429 | ≤ 160 | 250 | 280 | 315 | 580 to 800 | 40 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| X3CrNiMo17-13-3 | 1.4436 | ≤ 160 | 215 | 200 | 235 | 500 to 700 | 40 | – | 100 | – | yes | no h | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| X2CrNiMo18-14-3 | 1.4435 | ≤ 160 | 215 | 200 | 235 | 500 to 700 | 40 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| X2CrNiMoN17-13-5 | 1.4439 | ≤ 160 | 250 | 280 | 315 | 580 to 800 | 35 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| X6CrNiCuS18-9-2 | 1.4570 | ≤ 160 | 215 | 185 | 220 | 500 to 710 | 35 | – | – | – | no | no | |
| X3CrNiCu18-9-4 | 1.4567 | ≤ 160 | 215 | 175 | 210 | 450 to 650 | 45 | – | – | – | yes | yes | |
| X1NiCrMoCu25-20-5 | 1.4539 | ≤ 160 | 230 | 230 | 260 | 530 to 730 | 35 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| Special grades | |||||||||||||
| X5CrNi17-7 | 1.4319 | ≤ 16 | 215 | 190 | 225 | 500 to 700 | 45 | – | 100 | – | yes | noh | |
| X9CrNi18-9 | 1.4325 | ≤ 40 | 215 | 190 | 225 | 550 to 750 | 40 | – | – | – | yes | no | |
| X5CrNiN19-9 | 1.4315 | ≤ 40 | 215 | 270 | 310 | 550 to 750 | 40 | – | – | – | yes | noh | |
| X6CrNiNb18-10 | 1.4550 | ≤ 160 | 230 | 205 | 240 | 510 to 740 | 40 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| X1CrNiMoN25-22-2 | 1.4466 | ≤ 160 | 240 | 250 | 290 | 540 to 740 | 35 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | 240 | 250 | 290 | 540 to 740 | – | 30 | – | 60 | yes | yes | |||
| X6CrNiMoNb17-12-2 | 1.4580 | ≤ 160 | 230 | 215 | 250 | 510 to 740 | 35 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| X2CrNiMo18-15-4 | 1.4438 | ≤ 160 | 215 | 200 | 235 | 500 to 700 | 40 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| X1CrNiMoCuN24-22-8 | 1.4652 | ≤ 50 | 310 | 430 | 470 | 750 to 1000 | 40 | – | 100 | – | yes | yes | |
| X1CrNiSi18-5-4 | 1.4361 | ≤ 160 | 230 | 210 | 240 | 530 to 730 | 40 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| X11CrNiMnN19-8-6 | 1.4369 | ≤ 15 | 300 | 340 | 370 | 750 to 950 | 35 | 35 | 100 | 60 | yes | no | |
| X12CrMnNiN17-7-5 | 1.4372 | ≤ 160 | 260 | 230 | 370 | 750 to 950 | 40 | – | 100 | – | yes | no | |
| 160 < t ≤ 250 | 260 | 230 | 370 | 750 to 950 | – | 35 | – | 60 | yes | no | |||
| X8CrMnNiN18-9-5 | 1.4374 | ≤ 10 | 260 | 350 | 380 | 700 to 900 | 35 | – | – | – | yes | no | |
| X8CrMnCuNB17-8-3 | 1.4597 | ≤ 160 | 245 | 270 | 305 | 560 to 780 | 40 | – | 100 | – | yes | no | |
| X3CrNiCu19-9-2 | 1.4560 | ≤ 160 | 215 | 170 | 220 | 450 to 650 | 45 | – | 100 | – | yes | yes | |
| X3CrNiCuMo17-11-3-2 | 1.4578 | ≤ 160 | 215 | 175 | 220 | 450 to 650 | 45 | – | – | – | yes | yes | |
| X1NiCrMoCu31-27-4 | 1.4563 | ≤ 160 | 230 | 220 | 250 | 500 to 750 | 35 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| X1CrNiMoCuN25-25-5 | 1.4537 | ≤ 160 | 250 | 300 | 340 | 600 to 800 | 35 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| X1CrNiMoCuN20-18-7 | 1.4547 | ≤ 160 | 260 | 300 | 340 | 650 to 850 | 35 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 30 | – | 60 | |||||||||
| X2CrNiMoCuS17-10-2 | 1.4598 | ≤ 160 | 215 | 200 | 235 | 500 to 700 | 40 | – | 100 | – | yes | yes | |
| X1CrNiMoCuNW24-22-6 | 1.4659 | ≤ 160 | 290 | 420 | 460 | 800 to 1000 | 50 | – | 90 | – | yes | yes | |
| X1NiCrMoCuN25-20-7 | 1.4529 | ≤ 160 | 250 | 300 | 340 | 650 to 850 | 40 | – | 100 | – | yes | yes | |
| 160 < t ≤ 250 | – | 35 | – | 60 | |||||||||
| X2CrNiMnMoN25-18-6-5 | 1.4565 | ≤ 160 | – | 420 | 460 | 800 to 950 | 35 | – | 100 | – | yes | yes | |
| a Solution treatment may be omitted if the conditions for hot working and subsequent cooling are such that the requirements for the mechanical properties of the product and the resistance to Intergranular corrosion as defined in EN ISO 3651-2 are obtained. | |||||||||||||
| b Width across flats for hexagons. | |||||||||||||
| c Only for guidance. | |||||||||||||
| d The maximum HB-values may be raised by 100 HB or the tensile strength value may be raised by 200 MPa and the minimum elongation value may be lowered to 20 % for sections and bars of ≤ 35 mm thickness having a final cold deformation and for hot formed sections and bars of 8 mm thickness. | |||||||||||||
| e For rods, only the tensile strength values apply. | |||||||||||||
| f When tested according to EN ISO 3651-2. | |||||||||||||
| g See NOTE 2 to 6.4. | |||||||||||||
| h Sensitization treatment of 15 min at 700°C followed by cooling in air. | |||||||||||||
| *) 1MPa = 1 N/mm². | |||||||||||||
| Steel designation | Thickness t or diameter b d | Hardness c | 0,2 %-proof strength | Tensile strength | Elongation after fracture | Impact energy (ISO-V) | Resistance to intergranular corrosione | ||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Steel Name | Steel Number | mm | HB max. | Rp0,2d MPa*) min. | R m d MPa*) | Ad % min. (long.) | KV J min (long.) | in the delivery condition | In the sensitized conditionf | ||||
| Standard grades | |||||||||||||
| X3CrNiMoN27-5-2 | 1.4460 | ≤ 160 | 260 | 450 | 620 to 880 | 20 | 85 | yes | yes | ||||
| X2CrNiMoN22-5-3 | 1.4462 | ≤ 160 | 270 | 450 | 650 to 880 | 25 | 100 | yes | yes | ||||
| Special grades | |||||||||||||
| X2CrNiN23-4 | 1.4362 | ≤ 160 | 260 | 400 | 600 to 830 | 25 | 100 | yes | yes | ||||
| X2CrNiMoN29-7-2 | 1.4477 | ≤ 10 | 310 | 650 | 800 to 1050 | 25 | 100 | yes | yes | ||||
| 10 < t ≤ 160 | 310 | 550 | 750 to 1000 | 25 | 100 | yes | yes | ||||||
| X2CrNiMoCuN25-6-3 | 1.4507 | ≤ 160 | 270 | 500 | 700 to 900 | 25 | 100 | yes | yes | ||||
| X2CrNiMoN25-7-4 | 1.4410 | ≤ 160 | 290 | 530 | 730 to 930 | 25 | 100 | yes | yes | ||||
| X2CrNiMoCuWN25-7-4 | 1.4501 | ≤ 160 | 290 | 530 | 730 to 930 | 25 | 100 | yes | yes | ||||
| X2CrNiMoSi18-5-3 | 1.4424 | ≤ 50 | 260 | 450 | 700 to 900 | 25 | 100 | yes | yes | ||||
| 50 < t ≤ 160 | 260 | 400 | 680 to 900 | 25 | 100 | yes | yes | ||||||
| a Solution treatment may be omitted if the conditions for hot working and subsequent cooling are such that the requirement for the mechanical properties of the product and the resistance to intergranular corrosion as defined in EN ISO 3651-2 are obtained. | |||||||||||||
| b Width across flats for hexagons. | |||||||||||||
| c Only for guidance. | |||||||||||||
| d For rods, only the tensile strength values apply. | |||||||||||||
| e When tested according to EN ISO 3651-2. | |||||||||||||
| f See NOTE 2 to 6.4. | |||||||||||||
| *) 1MPa = 1 N/mm². | |||||||||||||
| Steel designation | Thickness t or diameter c d | 0,2 %-proof strength | Tensile strength | Elongation after fracture | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Steel Name | Steel Number | mm | Rp0,2 MPa*) min. | R m MPa*) | A5d % min. (long.) | ||||||||
| Standard grades | |||||||||||||
| X6Cr17 | 1.4016 | ≤ 10e | 320 | 500 to 750 | 8 | ||||||||
| 10 < t ≤ 16 | 300 | 480 to 750 | 8 | ||||||||||
| 16 < t ≤ 40 | 240 | 400 to 700 | 15 | ||||||||||
| 40 < t ≤ 63 | 240 | 400 to 700 | 15 | ||||||||||
| 63 < t ≤ 100 | 240 | 400 to 630 | 20 | ||||||||||
| X6CrMoS17 | 1.4105 | ≤ 10e | 330 | 530 to 780 | 7 | ||||||||
| 10 < t ≤ 16 | 310 | 500 to 780 | 7 | ||||||||||
| 16 < t ≤ 40 | 250 | 430 to 730 | 12 | ||||||||||
| 40 < t ≤ 63 | 250 | 430 to 730 | 12 | ||||||||||
| 63 < t ≤ 100 | 250 | 430 to 630 | 20 | ||||||||||
| X6CrMo17-1 | 1.4113 | ≤ 10e | 340 | 540 to 700 | 8 | ||||||||
| 10 < t ≤ 16 | 320 | 500 to 700 | 12 | ||||||||||
| 16 < t ≤ 40 | 280 | 440 to 700 | 15 | ||||||||||
| 40 < t ≤ 63 | 280 | 440 to 700 | 15 | ||||||||||
| 63 < t ≤ 100 | 280 | 440 to 660 | 18 | ||||||||||
| Special grades | |||||||||||||
| X2CrTi17 | 1.4520 | ≤ 10e | 320 | 500 to 750 | 8 | ||||||||
| 10 < t ≤ 16 | 300 | 480 to 750 | 10 | ||||||||||
| 16 < t ≤ 40 | 240 | 400 to 700 | 15 | ||||||||||
| 40 < t ≤ 50 | 240 | 400 to 700 | 15 | ||||||||||
| X3CrNb17 | 1.4511 | ≤ 10e | 320 | 500 to 750 | 8 | ||||||||
| 10 < t ≤ 16 | 300 | 480 to 750 | 10 | ||||||||||
| 16 < t ≤ 40 | 240 | 400 to 700 | 15 | ||||||||||
| 40 < t ≤ 50 | 240 | 400 to 700 | 15 | ||||||||||
| X6CrMoNb17-1 | 1.4526 | ≤ 10e | 340 | 540 to 700 | 8 | ||||||||
| 10 < t ≤ 16 | 320 | 500 to 700 | 12 | ||||||||||
| 16 < t ≤ 40 | 280 | 440 to 700 | 15 | ||||||||||
| 40 < t ≤ 50 | 280 | 440 to 700 | 15 | ||||||||||
| X2CrTiNb18 | 1.4509 | ≤ 10e | 320 | 500 to 750 | 8 | ||||||||
| 10 < t ≤ 16 | 300 | 480 to 750 | 10 | ||||||||||
| 16 < t ≤ 40 | 240 | 400 to 700 | 15 | ||||||||||
| 40 < t ≤ 50 | 240 | 400 to 700 | 15 | ||||||||||
| a Including cut lengths from wire. | |||||||||||||
| b Initial annealing treatment may be omitted if the conditions for previous hot working and subsequent cooling have been such that the requirements for the final mechanical properties of the product and the resistance to intergranular corrosion as defined in EN ISO 3651-2 are obtained. | |||||||||||||
| c Width across flats for hexagons. | |||||||||||||
| d Elongation A5 is valid only for dimensions of 5 mm and above. For smaller diameters, the minimum elongation has to be agreed upon at the time of enquiry and order. | |||||||||||||
| e In the range 1 mm ≤ d < 5 mm valid only for rounds. The mechanical properties of non round bars with thicknesses < 5 mm have to be agreed at the time of enquiry and order. | |||||||||||||
| *) 1MPa = 1 N/mm². | |||||||||||||
| Steel designation | Thickness t or diameter b d | Annealed | Quenched + tempered | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Steel Name | Steel Number | mm | R m MPa*) max. | HBc max. | Heat treatment condition. | Rp0,2 MPa*) min. | Rm MPa*) | A5d % min. | KV J min. | ||||
| (long.) | (tr.) | (long.) | (tr.) | ||||||||||
| Standard grades | |||||||||||||
| X12Cr13 | 1.4006 | ≤ 10e | 880 | 280 | +QT650 | 550 | 700 to 1000 | 9 | – | – | – | ||
| 10 < t ≤ 16 | 880 | 280 | 500 | 700 to 1000 | 9 | – | – | – | |||||
| 16 < t ≤ 40 | 800 | 250 | 450 | 650 to 930 | 10 | – | 25 | – | |||||
| 40 < t ≤ 63 | 760 | 230 | 450 | 650 to 880 | 10 | – | 25 | – | |||||
| 63 < t ≤ 160 | 730 | 220 | 450 | 650 to 850 | 15 | – | 25 | – | |||||
| X12CrS13 | 1.4005 | ≤ 10e | 880 | 280 | +QT650 | 550 | 700 to 1000 | 8 | – | – | – | ||
| 10 < t ≤ 16 | 880 | 280 | 500 | 700 to 1000 | 8 | – | – | – | |||||
| 16 < t ≤ 40 | 800 | 250 | 450 | 650 to 930 | 10 | – | – | – | |||||
| 40 < t ≤ 63 | 760 | 230 | 450 | 650 to 880 | 10 | – | – | – | |||||
| 63 < t ≤ 160 | 730 | 220 | 450 | 650 to 850 | 12 | – | – | – | |||||
| X20Cr13 | 1.4021 | ≤ 10e | 910 | 290 | +QT700 | 600 | 750 to 1000 | 8 | – | – | – | ||
| 10 < t ≤ 16 | 910 | 290 | 550 | 750 to 1000 | 8 | – | – | – | |||||
| 16 < t ≤ 40 | 850 | 260 | 500 | 700 to 950 | 10 | – | 25 | – | |||||
| 40 < t ≤ 63 | 800 | 250 | 500 | 700 to 900 | 12 | – | 25 | – | |||||
| 63 < t ≤ 160 | 760 | 230 | 500 | 700 to 850 | 13 | – | 25 | – | |||||
| X30Cr13 | 1.4028 | ≤ 10e | 950 | 305 | +QT850 | 700 | 900 to 1050 | 7 | – | – | – | ||
| 10 < t ≤ 16 | 950 | 305 | 650 | 900 to 1150 | 7 | – | – | – | |||||
| 16 < t ≤ 40 | 900 | 280 | 650 | 850 to 1100 | 9 | – | 15 | – | |||||
| 40 < t ≤ 63 | 840 | 260 | 650 | 850 to 1050 | 9 | – | 15 | – | |||||
| 63 < t ≤ 160 | 800 | 245 | 650 | 850 to 1000 | 10 | – | 15 | – | |||||
| X39Cr13 | 1.4031 | ≤ 10e | 950 | 305 | +QT800 | 700 | 850 to 1100 | 7 | – | – | – | ||
| 10 < t ≤ 16 | 950 | 305 | 700 | 850 to 1100 | 7 | – | – | – | |||||
| 16 < t ≤ 40 | 900 | 280 | 650 | 800 to 1050 | 8 | – | 12 | – | |||||
| 40 < t ≤ 63 | 840 | 260 | 650 | 800 to 1000 | 8 | – | 12 | – | |||||
| 63 < t ≤ 160 | 800 | 245 | 650 | 800 to 1000 | 10 | – | 12 | – | |||||
| X46Cr13 | 1.4034 | ≤ 10e | 950 | 305 | +QT850 | 700 | 900 to 1150 | 7 | – | – | – | ||
| 10 < t ≤ 16 | 950 | 305 | 700 | 900 to 1150 | 7 | – | – | – | |||||
| 16 < t ≤ 40 | 900 | 280 | 650 | 850 to 1100 | 8 | – | 12 | – | |||||
| 40 < t ≤ 63 | 840 | 260 | 650 | 850 to 1000 | 8 | – | 12 | – | |||||
| 63 < t ≤ 160 | 800 | 245 | 650 | 850 to 1000 | 10 | – | 12 | – | |||||
| X14CrMoS17 | 1.4104 | ≤ 10e | 880 | 280 | +QT650 | 580 | 700 to 980 | 7 | – | – | – | ||
| 10 < t ≤ 16 | 880 | 280 | 530 | 700 to 980 | 7 | – | – | – | |||||
| 16 < t ≤ 40 | 800 | 250 | 500 | 650 to 930 | 9 | – | – | – | |||||
| 40 < t ≤ 63 | 760 | 230 | 500 | 650 to 880 | 10 | – | – | – | |||||
| 63 < t ≤ 160 | 730 | 220 | 500 | 650 to 850 | 10 | – | – | – | |||||
| X39CrMo17-1 | 1.4122 | ≤ 10e | 1000 | 340 | +QT750 | 650 | 800 to 1050 | 8 | – | – | – | ||
| 10 < t ≤ 16 | 1000 | 340 | 600 | 800 to 1050 | 8 | – | – | – | |||||
| 16 < t ≤ 40 | 980 | 310 | 550 | 800 to 1000 | 10 | – | 20 | – | |||||
| 40 < t ≤ 63 | 930 | 290 | 550 | 750 to 950 | 12 | – | 20 | – | |||||
| 63 < t ≤ 160 | 900 | 280 | 550 | 750 to 950 | 12 | – | 14 | – | |||||
| X17CrNi16-2 | 1.4057 | ≤ 10e | 1050 | 330 | +QT800 | 750 | 850 to 1100 | 7 | – | – | – | ||
| 10 < t ≤ 16 | 1050 | 330 | 700 | 850 to 1100 | 7 | – | – | – | |||||
| 16 < t ≤ 40 | 1000 | 310 | 650 | 800 to 1050 | 9 | – | 25 | – | |||||
| 40 < t ≤ 63 | 950 | 295 | 650 | 800 to 1000 | 12 | – | 25 | – | |||||
| 63 < t ≤ 160 | 950 | 295 | 650 | 800 to 950 | 12 | – | 20 | – | |||||
| X4CrNiMo16-5-1 | 1.4418 | ≤ 10e | 1150 | 380 | +QT900 | 750 | 900 to 1150 | 10 | – | – | – | ||
| 10 < t ≤ 16 | 1150 | 380 | 750 | 900 to 1150 | 10 | – | – | – | |||||
| 16 < t ≤ 40 | 1100 | 320 | 700 | 900 to 1100 | 12 | – | 80 | – | |||||
| 40 < t ≤ 63 | 1100 | 320 | 700 | 900 to 1100 | 16 | – | 80 | – | |||||
| 63 < t ≤ 160 | 1100 | 320 | 700 | 900 to 1100 | 16 | – | 80 | – | |||||
| 160 < t ≤ 250 | 1100 | 320 | 700 | 900 to 1100 | – | 14 | – | 60 | |||||
| Special grades | |||||||||||||
| X29CrS13 | 1.4029 | ≤ 10e | 950 | 305 | +QT850 | 750 | 900 to 1100 | 8 | – | – | – | ||
| 10 < t ≤ 16 | 950 | 305 | 700 | 900 to 1100 | 8 | – | – | – | |||||
| 16 < t ≤ 40 | 900 | 280 | 650 | 850 to 1100 | 10 | – | – | – | |||||
| 40 < t ≤ 63 | 840 | 260 | 650 | 850 to 1050 | 10 | – | – | – | |||||
| 63 < t ≤ 160 | 800 | 245 | 650 | 850 to 1000 | 12 | – | – | – | |||||
| X46CrS13 | 1.4035 | ≤ 10e | 880 | 280 | – | – | – | – | – | – | – | ||
| 10 < t ≤ 16 | 880 | 280 | – | – | – | – | – | – | |||||
| 16 < t ≤ 40 | 800 | 250 | – | – | – | – | – | – | |||||
| 40 < t ≤ 63 | 760 | 230 | – | – | – | – | – | – | |||||
| a Including cut lengths from wire. | |||||||||||||
| b Width across flats for hexagons. | |||||||||||||
| c For information only. | |||||||||||||
| d Elongation A5 is valid only for dimensions of 5 mm and above. For smaller diameters, the minimum elongation has to be agreed upon at the time of enquiry and order. | |||||||||||||
| e In the range 1 mm ≤ d < 5 mm valid only for rounds. The mechanical properties of non round bars with thicknesses < 5 mm have to be agreed at the time of enquiry and order. | |||||||||||||
| *) 1MPa = 1 N/mm². | |||||||||||||
| Steel designation | Thickness t or diameter c d | Annealed | Precipitation hardened | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Steel Name | Steel Number | mm | R m MPa*) max. | HBc max. | Heat treatment condition | Rp0,2 MPa*) min. | R m MPa*) | A5d % min. (long.) | KV J min. (long.) | ||||
| Standard grade | |||||||||||||
| X5CrNiCuNb16-4 | 1.4542 | ≤ 10e | 1200 | 360 | +P800 | 600 | 900 to 1100 | 10 | – | ||||
| 10 < t ≤ 16 | 1200 | 360 | 600 | 900 to 1100 | 10 | – | |||||||
| 16 < t ≤ 40 | 1200 | 360 | 520 | 800 to 1050 | 12 | 75 | |||||||
| 40 < t ≤ 63 | 1200 | 360 | 520 | 800 to 1000 | 18 | 75 | |||||||
| 63 < t ≤ 160 | 1200 | 360 | 520 | 800 to 950 | 18 | 75 | |||||||
| ≤ 100 | – | – | +P930 | 720 | 930 to 1100 | 12 | 40 | ||||||
| ≤ 100 | – | – | +P960 | 790 | 960 to 1160 | 10 | – | ||||||
| ≤ 100 | – | – | +P1070 | 1000 | 1070 to 1270 | 10 | – | ||||||
| Special grade | |||||||||||||
| X5NiCrTiMoVB25-15-2 | 1.4606 | ≤ 10e | 850 | 240 | +P880 | 750 | 950 to 1200 | 15 | 30 | ||||
| 10 < t ≤ 16 | 800 | 230 | 750 | 950 to 1150 | 15 | 30 | |||||||
| 16 < t ≤ 40 | 800 | 230 | 600 | 900 to 1150 | 18 | 40 | |||||||
| 40 < t ≤ 50 | 700 | 212 | 550 | 880 to 1150 | 20 | 40 | |||||||
| a Including cut lengths from wire. | |||||||||||||
| b Width across flats for hexagons. | |||||||||||||
| c For information only. | |||||||||||||
| d Elongation A5 is valid only for dimensions of 5 mm and above. For smaller diameters, the minimum elongation has to be agreed upon at the time of enquiry and order. | |||||||||||||
| e In the range 1 mm ≤ d < 5 mm valid only for rounds. The mechanical properties of non round bars with thicknesses < 5 mm have to be agreed at the time of enquiry and order. | |||||||||||||
| *) 1MPa = 1 N/mm². | |||||||||||||
| Steel designation | Thickness t or diameter c d | Solution annealed | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Steel Name | Steel Number | mm | Rp0,2 MPa*) min. | R m MPa*) | A5d % min. | KV J min. | |||||||
| (long.) | (tr.) | (long.) | (tr.) | ||||||||||
| Standard grades | |||||||||||||
| X2CrNi18-9 | 1.4307 | ≤ 10e | 400 | 600 to 930 | 25 | – | – | – | |||||
| 10 < t ≤ 16 | 380 | 600 to 930 | 25 | – | – | – | |||||||
| 16 < t ≤ 40 | 175 | 500 to 830 | 30 | – | 100 | – | |||||||
| 40 < t ≤ 63 | 175 | 500 to 830 | 30 | – | 100 | – | |||||||
| 63 < t ≤ 160 | 175 | 500 to 700 | 45 | – | 100 | – | |||||||
| 160 < t ≤ 250 | 175 | 500 to 700 | – | 35 | – | 60 | |||||||
| X2CrNi19-11 | 1.4306 | ≤ 10e | 400 | 600 to 930 | 25 | – | – | – | |||||
| 10 < t ≤ 16 | 380 | 600 to 930 | 25 | – | – | – | |||||||
| 16 < t ≤ 40 | 180 | 460 to 830 | 30 | – | 100 | – | |||||||
| 40 < t ≤ 63 | 180 | 460 to 830 | 30 | – | 100 | – | |||||||
| 63 < t ≤ 160 | 180 | 460 to 680 | 45 | – | 100 | – | |||||||
| 160 < t ≤ 250 | 180 | 460 to 680 | – | 35 | – | 60 | |||||||
| X5CrNi18-10 | 1.4301 | ≤ 10e | 400 | 600 to 950 | 25 | – | – | – | |||||
| 10 < t ≤ 16 | 400 | 600 to 950 | 25 | – | – | – | |||||||
| 16 < t ≤ 40 | 190 | 600 to 850 | 30 | – | 100 | – | |||||||
| 40 < t ≤ 63 | 190 | 580 to 850 | 30 | – | 100 | – | |||||||
| 63 < t ≤ 160 | 190 | 500 to 700 | 45 | – | 100 | – | |||||||
| 160 < t ≤ 250 | 190 | 500 to 700 | – | 35 | – | 60 | |||||||
| X8CrNiS18-9 | 1.4305 | ≤ 10e | 400 | 600 to 950 | 15 | – | – | – | |||||
| 10 < t ≤ 16 | 400 | 600 to 950 | 15 | – | – | – | |||||||
| 16 < t ≤ 40 | 190 | 500 to 850 | 20 | – | 100 | – | |||||||
| 40 < t ≤ 63 | 190 | 500 to 850 | 20 | – | 100 | – | |||||||
| 63 < t ≤ 160 | 190 | 500 to 750 | 35 | – | 100 | – | |||||||
| X6CrNiTi18-10 | 1.4541 | ≤ 10e | 400 | 600 to 950 | 25 | – | – | – | |||||
| 10 < t ≤ 16 | 380 | 580 to 950 | 25 | – | – | – | |||||||
| 16 < t ≤ 40 | 190 | 500 to 850 | 30 | – | 100 | – | |||||||
| 40 < t ≤ 63 | 190 | 500 to 850 | 30 | – | 100 | – | |||||||
| 63 < t ≤ 160 | 190 | 500 to 700 | 40 | – | 100 | – | |||||||
| X2CrNiMo17-12-2 | 1.4404 | ≤ 10e | 400 | 600 to 930 | 25 | – | – | – | |||||
| 10 < t ≤ 16 | 380 | 580 to 930 | 25 | – | – | – | |||||||
| 16 < t ≤ 40 | 200 | 500 to 830 | 30 | – | 100 | – | |||||||
| 40 < t ≤ 63 | 200 | 500 to 830 | 30 | – | 100 | – | |||||||
| 63 < t ≤ 160 | 200 | 500 to 700 | 40 | – | 100 | – | |||||||
| 160 < t ≤ 250 | 200 | 500 to 700 | – | 30 | – | 60 | |||||||
| X5CrNiMo17-12-2 | 1.4401 | ≤ 10e | 400 | 600 to 950 | 25 | – | – | – | |||||
| 10 < t ≤ 16 | 380 | 580 to 950 | 25 | – | – | – | |||||||
| 16 < t ≤ 40 | 200 | 500 to 850 | 30 | – | 100 | – | |||||||
| 40 < t ≤ 63 | 200 | 500 to 850 | 30 | – | 100 | – | |||||||
| 63 < t ≤ 160 | 200 | 500 to 700 | 40 | – | 100 | – | |||||||
| 160 < t ≤ 250 | 200 | 500 to 700 | – | 30 | – | 60 | |||||||
| X6CrNiMoTi17-12-2 | 1.4571 | ≤ 10e | 400 | 600 to 950 | 25 | – | – | – | |||||
| 10 < t ≤ 16 | 380 | 580 to 950 | 25 | – | – | – | |||||||
| 16 < t ≤ 40 | 200 | 500 to 850 | 30 | – | 100 | – | |||||||
| 40 < t ≤ 63 | 200 | 500 to 850 | 30 | – | 100 | – | |||||||
| 63 < t ≤ 160 | 200 | 500 to 700 | 40 | – | 100 | – | |||||||
| 160 < t ≤ 250 | 200 | 500 to 700 | – | 30 | – | 60 | |||||||
| X2CrNiMo17-12-3 | 1.4432 | ≤ 10e | 400 | 600 to 930 | 25 | – | – | – | |||||
| 10 < t ≤ 16 | 380 | 600 to 880 | 25 | – | – | – | |||||||
| 16 < t ≤ 40 | 200 | 500 to 850 | 30 | – | 100 | – | |||||||
| 40 < t ≤ 63 | 200 | 500 to 850 | 30 | – | 100 | – | |||||||
| 63 < t ≤ 160 | 200 | 500 to 700 | 40 | – | 100 | – | |||||||
| 160 < t ≤ 250 | 200 | 500 to 700 | – | 30 | – | 60 | |||||||
| X3CrNiMo17-13-3 | 1.4436 | ≤ 10e | 400 | 600 to 950 | 25 | – | – | – | |||||
| 10 < t ≤ 16 | 400 | 600 to 950 | 25 | – | – | – | |||||||
| 16 < t ≤ 40 | 200 | 500 to 850 | 30 | – | 100 | – | |||||||
| 40 < t ≤ 63 | 190 | 500 to 850 | 30 | – | 100 | – | |||||||
| 63 < t ≤ 160 | 200 | 500 to 700 | 40 | – | 100 | – | |||||||
| 160 < t ≤ 250 | 200 | 500 to 700 | – | 30 | – | 60 | |||||||
| X2CrNiMo18-14-3 | 1.4435 | ≤ 10e | 400 | 600 to 950 | 25 | – | – | – | |||||
| 10 < t ≤ 16 | 400 | 600 to 950 | 25 | – | – | – | |||||||
| 16 < t ≤ 40 | 235 | 500 to 850 | 30 | – | 100 | – | |||||||
| 40 < t ≤ 63 | 235 | 500 to 850 | 30 | – | 100 | – | |||||||
| 63 < t ≤ 160 | 235 | 500 to 700 | 40 | – | 100 | – | |||||||
| 160 < t ≤ 250 | 235 | 500 to 700 | – | 30 | – | 60 | |||||||
| X6CrNiCuS18-9-2 | 1.4570 | ≤ 10e | 400 | 600 to 950 | 15 | – | – | – | |||||
| 10 < t ≤ 16 | 400 | 600 to 950 | 15 | – | – | – | |||||||
| 16 < t ≤ 40 | 185 | 500 to 910 | 20 | – | – | – | |||||||
| 40 < t ≤ 63 | 185 | 500 to 910 | 20 | – | – | – | |||||||
| 63 < t ≤ 160 | 185 | 500 to 710 | 35 | – | – | – | |||||||
| X3CrNiCu18-9-4 | 1.4567 | ≤ 10e | 400 | 600 to 850 | 25 | – | – | – | |||||
| 10 < t ≤ 16 | 340 | 600 to 850 | 25 | – | – | – | |||||||
| 16 < t ≤ 40 | 175 | 450 to 800 | 30 | – | 100 | – | |||||||
| 40 < t ≤ 63 | 175 | 450 to 800 | 30 | – | 100 | – | |||||||
| 63 < t ≤ 160 | 175 | 450 to 650 | 40 | – | 100 | – | |||||||
| X1NiCrMoCu25-20-5 | 1.4539 | ≤ 10e | 400 | 600 to 930 | 20 | – | – | – | |||||
| 10 < t ≤ 16 | 400 | 600 to 930 | 20 | – | – | – | |||||||
| 16 < t ≤ 40 | 230 | 530 to 880 | 25 | – | 100 | – | |||||||
| 40 < t ≤ 63 | 230 | 530 to 880 | 25 | – | 100 | – | |||||||
| 63 < t ≤ 160 | 230 | 530 to 730 | 35 | – | 100 | – | |||||||
| 160 < t ≤ 250 | 230 | 530 to 730 | – | 30 | – | 60 | |||||||
| Special grades | |||||||||||||
| X3CrNiCu19-9-2 | 1.4560 | ≤ 10e | 400 | 600 to 800 | 25 | – | – | – | |||||
| 10 < t ≤ 16 | 340 | 600 to 800 | 25 | – | – | – | |||||||
| 16 < t ≤ 40 | 175 | 450 to 750 | 30 | – | – | – | |||||||
| 40 < t ≤ 63 | 175 | 450 to 750 | 30 | – | – | – | |||||||
| 63 < t ≤ 160 | 175 | 450 to 650 | 45 | – | – | – | |||||||
| X3CrNiCuMo17-11-3-2 | 1.4578 | ≤ 10e | 400 | 600 to 850 | 20 | – | – | – | |||||
| 10 < t ≤ 16 | 340 | 600 to 850 | 20 | – | – | – | |||||||
| 16 < t ≤ 40 | 175 | 450 to 800 | 30 | – | – | – | |||||||
| 40 < t ≤ 63 | 175 | 450 to 800 | 30 | – | – | – | |||||||
| 63 < t ≤ 160 | 175 | 450 to 650 | 45 | – | – | – | |||||||
| X2CrNiMoCuS17-10-2 | 1.4598 | ≤ 10e | 400 | 600 to 930 | 15 | – | – | – | |||||
| 10 < t ≤ 16 | 400 | 600 to 900 | 20 | – | – | – | |||||||
| 16 < t ≤ 40 | 200 | 500 to 850 | 25 | – | – | – | |||||||
| 40 < t ≤ 63 | 200 | 500 to 800 | 30 | – | – | – | |||||||
| 63 < t ≤ 160 | 200 | 500 to 700 | 40 | – | – | – | |||||||
| a Including cut lengths from wire. | |||||||||||||
| b Inital solution treatment may be omitted if the conditions for previous hot-working and subsequent cooling have been such that the requirements for the mechanical properties of the product and the resistance to intergranular corrosion as defined in EN ISO 3651-2 are obtained. | |||||||||||||
| c Width across flats for hexagons. | |||||||||||||
| d Elongation is valid only for dimensions of 5 mm and above. For smaller diameters, the minimum elongation has to be agreed upon at the time of enquiry and order. | |||||||||||||
| e In the range 1 mm ≤ d < 5 mm valid only for rounds. The mechanical properties of non round bars with thicknesses < 5 mm have to be agreed at the time of enquiry and order. | |||||||||||||
| *) 1MPa = 1 N/mm². | |||||||||||||
| Steel designation | Thickness t or diameter c d | Solution annealed | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Steel Name | Steel Number | mm | Rp0,2 MPa*) min. | R m MPa*) | A5d % min. (long.) | KV J min. (long.) | |||||||
| Standard grades | |||||||||||||
| X3CrNiMoN27-5-2 | 1.4460 | ≤ 10e | 610 | 770 to 1030 | 12 | – | |||||||
| 10 < t ≤ 16 | 560 | 770 to 1030 | 12 | – | |||||||||
| 16 < t ≤ 40 | 460 | 620 to 950 | 15 | 85 | |||||||||
| 40 < t ≤ 63 | 460 | 620 to 950 | 15 | 85 | |||||||||
| 63 < t ≤ 160 | 460 | 620 to 880 | 20 | 85 | |||||||||
| X2CrNiMoN22-5-3 | 1.4462 | ≤ 10e | 650 | 850 to 1150 | 12 | – | |||||||
| 10 < t ≤ 16 | 650 | 850 to 1100 | 12 | – | |||||||||
| 16 < t ≤ 40 | 450 | 650 to 1000 | 15 | 100 | |||||||||
| 40 < t ≤ 63 | 450 | 650 to 1000 | 15 | 100 | |||||||||
| 63 < t ≤ 160 | 450 | 650 to 880 | 25 | 100 | |||||||||
| Special grade | |||||||||||||
| X2CrNiMoCuN25-6-3 | 1.4507 | ≤ 10e | –f | –f | –f | – | |||||||
| 10 < t ≤ 16 | –f | –f | –f | – | |||||||||
| 16 < t ≤ 40 | 500 | 700 to 900 | 25 | 100 | |||||||||
| 40 < t ≤ 63 | 500 | 700 to 900 | 25 | 100 | |||||||||
| 63 < t ≤ 160 | 500 | 700 to 900 | 25 | 100 | |||||||||
| a Including cut lengths from wire. | |||||||||||||
| b Inital solution treatment may be omitted if the conditions for previous hot-working and subsequent cooling have been such that the requirements for the mechanical properties of the product and the resistance to intergranular corrosion as defined in EN ISO 3651-2 are obtained. | |||||||||||||
| c Width across flats for hexagons. | |||||||||||||
| d Elongation is valid only for dimensions of 5 mm and above. For smaller diameters, the minimum elongation has to be agreed upon at the time of enquiry and order. | |||||||||||||
| e In the range 1 mm ≤ d < 5 mm valid only for rounds. The mechanical properties of non round bars with thicknesses < 5 mm have to be agreed at the time of enquiry and order. | |||||||||||||
| f To be agreed upon at the time of enquiry and order. | |||||||||||||
| *) 1MPa = 1 N/mm². | |||||||||||||